Building a circuit that does not work is frustrating. Debugging a circuit on a breadboard -- measuring voltages, swapping components, checking connections -- can take hours. And if a design error sends too much current through a component, you might damage expensive parts.
Circuit simulation solves this by letting you test your design on a computer before building anything physical. You draw your schematic, set component values, and run a simulation that calculates the exact voltages, currents, and waveforms throughout your circuit. If something is wrong, you fix it in software, not in solder.
This guide explains the three main types of circuit simulation, how to interpret the results, and how simulation fits into a practical design workflow.
What Is Circuit Simulation?
Circuit simulation uses mathematical models of electronic components to predict how a circuit will behave under specified conditions. The industry-standard simulation engine is SPICE (Simulation Program with Integrated Circuit Emphasis), originally developed at UC Berkeley in the 1970s. Modern simulators are based on SPICE or compatible engines.
A simulator takes three inputs:
- The netlist: A description of your circuit -- which components are connected to which nodes.
- Component models: Mathematical descriptions of how each component behaves (resistance, capacitance, transistor characteristics, etc.).
- Analysis type: What you want to simulate (DC operating point, transient response, AC frequency response, etc.).
The simulator outputs the voltages at every node and the currents through every component, either as single values (DC analysis) or as waveforms over time or frequency (transient and AC analysis).
Why Simulate Before Building?
Catch Design Errors Early
A simulation reveals problems that are invisible on a schematic:
- A resistor that is too small, causing excessive current
- A voltage divider that does not produce the expected output voltage
- An op-amp that saturates because the gain is too high
- A filter that does not cut off at the right frequency
Save Components and Time
Building and debugging a physical circuit takes time and can destroy components. Simulation lets you iterate rapidly: change a resistor value, rerun the simulation, and see the result in seconds.
Verify Performance Specs
If your circuit needs to meet specific performance targets (gain, bandwidth, ripple voltage, rise time), simulation gives you quantitative measurements before you build.
Explore "What If" Scenarios
What happens if the supply voltage drops 10%? What if the temperature changes? What if the load resistance varies? Simulation lets you sweep parameters and see the effects across a range of conditions.
Document Your Design
Simulation results serve as design documentation. When you hand off a design to manufacturing or to another engineer, the simulation data shows that the circuit meets its specifications.
Type 1: DC Analysis (Operating Point)
DC analysis calculates the steady-state voltages and currents in your circuit when all inputs are constant. No time variation, no frequency effects -- just the static operating point.
What It Tells You
- The voltage at every node in the circuit
- The current through every component
- Power dissipation in each component
- Whether any component is operating outside its limits
When to Use DC Analysis
- Verifying a voltage divider output
- Checking the bias point of a transistor amplifier
- Confirming that a voltage regulator produces the correct output
- Ensuring that LED current-limiting resistors are sized correctly
- Verifying power supply loading
Example: Voltage Divider
Consider a voltage divider with R1 = 10K ohm (top) and R2 = 10K ohm (bottom), powered by a 5V source.
DC analysis results:
- Node voltage at the junction: 2.5V (as expected: 5V x 10K / (10K + 10K))
- Current through both resistors: 0.25mA (5V / 20K ohm)
- Power in each resistor: 0.625mW
Now change R2 to 4.7K ohm:
- Junction voltage: 5V x 4.7K / (10K + 4.7K) = 1.60V
- Current: 5V / 14.7K = 0.34mA
The simulation gives you these numbers instantly for any combination of values.
Reading DC Results
In most simulators, DC results are displayed as:
- Node voltage annotations on the schematic: Each node shows its voltage relative to ground.
- Branch current annotations: Arrows showing current magnitude and direction through each component.
- A table of values: Node voltages and branch currents listed in a results panel.
In CircuitDiagramMaker, DC simulation results are overlaid directly on your schematic. Each node lights up with its voltage, and each component shows its current. This makes it immediately obvious where problems are -- a node at 0V when you expected 5V jumps out visually.
Type 2: Transient Analysis (Time Domain)
Transient analysis simulates your circuit over time. It shows how voltages and currents change from one moment to the next, which is essential for circuits with time-varying signals (oscillators, pulse circuits, motor drivers, switch-mode power supplies).
What It Tells You
- Waveform shapes (sine, square, sawtooth, etc.)
- Rise time and fall time
- Overshoot and ringing
- Settling time
- Peak voltages and currents
- Timing relationships between signals
When to Use Transient Analysis
- Designing oscillator circuits (555 timer, RC oscillators)
- Analyzing filter step response
- Verifying PWM signal behavior
- Checking startup behavior of power supplies
- Simulating motor driver switching patterns
- Testing digital logic timing
Transient Simulation Parameters
- Step time (time step): The interval between calculated points. Smaller steps = more accuracy but longer simulation time. Start with T_step = T_total / 1000.
- Stop time (total simulation time): How long the simulation runs. Set this to show at least 2-3 complete cycles of the lowest-frequency signal.
Example: RC Filter Step Response
A low-pass RC filter (R = 10K, C = 0.1uF) driven by a step function (0V to 5V at t=0):
- Time constant: tau = R x C = 10K x 0.1uF = 1ms
- Output rises to 63.2% of final value (3.16V) in 1ms
- Output reaches 99.3% of final value (4.97V) in 5 time constants (5ms)
The transient simulation shows the smooth exponential curve as the capacitor charges, giving you the exact timing and voltage at every point.
Reading Transient Results
Transient results are displayed as waveforms plotted against time:
- X-axis: Time (seconds, milliseconds, microseconds)
- Y-axis: Voltage or current
- Multiple traces: You can plot voltages at different nodes or currents through different components on the same graph for comparison.
Use cursors to measure:
- Period and frequency of periodic signals
- Rise time (10% to 90% of final value)
- Peak values and DC offset
- Phase difference between two signals
CircuitDiagramMaker's waveform viewer lets you add probes to any node, overlay multiple traces, zoom into regions of interest, and measure timing values directly on the waveform.
Type 3: AC Analysis (Frequency Domain)
AC analysis shows how your circuit responds to signals at different frequencies. It calculates the gain (magnitude) and phase shift of the output relative to the input across a range of frequencies.
What It Tells You
- Gain vs. frequency (Bode magnitude plot): How much the circuit amplifies or attenuates signals at each frequency.
- Phase vs. frequency (Bode phase plot): How much the circuit delays the signal at each frequency.
- Cutoff frequency: The frequency where the gain drops by 3dB (half-power point).
- Bandwidth: The range of frequencies where the circuit operates within specification.
- Resonant frequency: For circuits with inductors and capacitors, the frequency where they interact most strongly.
When to Use AC Analysis
- Designing audio filters (high-pass, low-pass, band-pass)
- Analyzing amplifier frequency response
- Tuning radio receiver circuits
- Checking power supply loop stability
- Verifying EMI filter performance
AC Simulation Parameters
- Start frequency: The lowest frequency to simulate (e.g., 1 Hz or 10 Hz).
- Stop frequency: The highest frequency (e.g., 1 MHz or 100 MHz).
- Points per decade: How many frequency points to calculate per factor-of-10 range. 10-20 points per decade gives a smooth curve.
- Sweep type: Usually logarithmic (equal spacing on a log scale), which makes sense because frequency response is typically plotted on a log scale.
Example: Low-Pass RC Filter AC Response
The same RC filter (R = 10K, C = 0.1uF):
- Cutoff frequency: f_c = 1 / (2 x pi x R x C) = 1 / (2 x 3.14159 x 10000 x 0.0000001) = 159.2 Hz
- Below 159 Hz: gain is approximately 0dB (signal passes through unchanged)
- At 159 Hz: gain is -3dB (signal is attenuated to 70.7% of input)
- Above 159 Hz: gain drops at -20dB per decade (each 10x increase in frequency reduces gain by 10x)
The AC simulation plots this as a smooth curve on a Bode plot, showing exactly where the filter starts cutting off and how steep the rolloff is.
Reading AC Results (Bode Plots)
Bode plots use logarithmic scales:
- X-axis: Frequency on a log scale (1, 10, 100, 1K, 10K, ...)
- Y-axis (magnitude): Gain in decibels (dB). 0dB = unity gain. -20dB = 1/10 gain. +20dB = 10x gain.
- Y-axis (phase): Phase shift in degrees. 0 degrees = no phase shift. -90 degrees = output lags input by 1/4 cycle.
Key things to identify:
- Passband: The flat region where the circuit passes signals without attenuation.
- Stopband: The region where signals are significantly attenuated.
- Cutoff frequency (-3dB point): The transition between passband and stopband.
- Roll-off rate: How quickly gain drops in the stopband (-20dB/decade for first-order, -40dB/decade for second-order, etc.).
Practical Simulation Workflow
Here is a step-by-step workflow for using simulation effectively:
Step 1: Draw the Schematic
Create your circuit schematic with accurate component values. Every resistor, capacitor, inductor, and semiconductor should have the correct value and model.
Step 2: Run DC Analysis First
Always start with DC analysis, even if you ultimately need transient or AC results. DC analysis verifies that:
- Power supply voltages are correct
- Transistor bias points are reasonable
- No component has excessive current
If DC analysis shows problems, fix them before proceeding to dynamic simulations.
Step 3: Run Transient or AC Analysis
Based on your circuit's purpose, run the appropriate dynamic analysis:
- Time-domain behavior: transient analysis
- Frequency-domain behavior: AC analysis
- Both: run both and cross-check results
Step 4: Iterate
Adjust component values based on simulation results and rerun. This is where simulation pays for itself -- each iteration takes seconds, not hours.
Step 5: Verify with a Physical Build
Once simulation shows your circuit meets specifications, build it on a breadboard and measure with real instruments. Compare measurements to simulation. Small differences are normal due to component tolerances and parasitics; large differences indicate a modeling issue.
Limitations of Simulation
Simulation is powerful but not perfect:
- Component models are approximations. Real components have parasitic effects (stray capacitance, inductance, resistance) that simplified models may not capture.
- Simulation does not show physical layout effects. Wire length, component placement, and proximity to other circuits affect performance in ways that schematic-level simulation cannot predict.
- Temperature effects require explicit modeling. Most basic simulations assume room temperature (25 degrees C). If your circuit operates in extreme temperatures, you need temperature-aware models.
- Simulation cannot test mechanical connections. A cold solder joint, a loose wire nut, or a corroded connector will never show up in simulation.
Despite these limitations, simulation catches the vast majority of design errors and dramatically reduces the time from concept to working prototype.
Try Our Built-In SPICE Simulator Free
CircuitDiagramMaker includes a full-featured circuit simulator right in the browser:
- DC analysis: See node voltages and branch currents overlaid on your schematic
- Transient analysis: Plot voltage and current waveforms over time
- AC analysis: Generate Bode plots showing gain and phase vs. frequency
- Waveform viewer: Zoom, pan, and measure waveforms with cursors
- No installation required: Everything runs in your browser
- Free to use: Simulation is included with every account
Draw your circuit, click Simulate, and see results in seconds.
Try our built-in SPICE simulator free
Key Takeaways
- Circuit simulation lets you test your design on a computer before building anything physical, saving time and components.
- DC analysis shows static voltages and currents -- always run this first to verify basic circuit operation.
- Transient analysis shows how circuits behave over time -- essential for timing circuits, filters, and switching designs.
- AC analysis shows frequency response using Bode plots -- critical for filter design, amplifier bandwidth, and stability analysis.
- Start with DC analysis to verify operating points, then run dynamic analyses to verify performance.
- Simulation catches the majority of design errors but does not replace physical testing with real components.
- Modern browser-based simulators make SPICE analysis accessible to everyone, from beginners to professionals.
Originally published at https://circuitdiagrammaker.app/blog/circuit-simulation-test-designs-before-building.
