Stop overpaying for your boards. From laminate choices to panel utilization, learn how to cut PCB costs without sacrificing reliability or performance.

Introduction

I have spent over 15 years reviewing Gerber files and production quotes, and I’ve seen countless designs where the BOM cost is optimized to the penny while the bare board price remains 30% higher than necessary.

Usually, this isn't due to one major error, but a dozen “default” design choices that ignore how a fabrication house actually operates. If we want to reduce costs, we have to stop designing in a vacuum and start designing for the production panel.

How Panel Utilization Drives Your Unit Price

Fabrication houses do not buy material by the size of your individual PCB; they buy it in large production panels, typically:

• 18" × 24"
• 18" × 12"
• 21" × 24"

When you submit an order, you are effectively renting a percentage of that panel. If your board dimensions result in poor nesting, you are paying for the “dust” (the scrap material) that the router turns into waste.

Remember: the larger the board, the greater the cost. Board size has a direct relationship to the final price a customer will pay.

I once worked on a project where a client’s board was 105mm wide. By trimming just 6mm from the width—moving a few non-critical connectors—we were able to fit an extra column of boards onto a standard production panel.

That single change reduced the unit price by 15% without altering a single electrical characteristic.

Before you finalize your mechanical outline, ask your fabricator what their standard panel sizes are and calculate your yield.

When to Stick with Standard Tg Laminates

The choice of base material is the most significant cost driver after board size.

Many engineers default to High-Tg FR-4 because it sounds safer for lead-free reflow. However, unless your board is:

• 8 layers or more
• operating continuously above 130°C

you might be paying a premium for performance you don't need.

Standard Tg (130°C–140°C) is perfectly fine for most double-sided and simple 4-layer designs.

Mid-Tg (150°C) is often the sweet spot for reliability in lead-free assembly without the 20–30% price jump of High-Tg (170°C–180°C) materials.

I only mandate High-Tg when the Z-axis expansion of a thick multilayer board threatens the integrity of plated through-holes during multiple reflow cycles.

Why 0.2mm Vias Cost More Than You Think

Every hole on your board requires a physical drill bit. As those bits get smaller, they become more expensive and break more easily.

Standard mechanical drilling is highly efficient down to 0.3mm (12 mil).

Once you drop to 0.2mm (8 mil) or smaller, the fabricator must:

• slow spindle speeds
• reduce drill hit counts
• tighten process controls

I've seen yield rates drop and prices climb the moment a designer specifies a 0.15mm via on a standard 1.6mm board.

This creates a high aspect ratio (board thickness divided by drill diameter). If your aspect ratio exceeds 10:1, plating chemistry struggles to flow properly through the hole, leading to weak barrels and possible field failures.

If you can stay at 0.3mm vias, you remain in the high-yield, low-cost sweet spot of nearly every PCB fab house in the world.

Choosing the Right Surface Finish for Your Budget

ENIG (Electroless Nickel Immersion Gold) is beautiful, flat, and excellent for fine-pitch SMT components.

It is also expensive.

For many through-hole or standard SMT designs, HASL or Lead-Free HASL is significantly cheaper and provides excellent solderability.

I’ve recommended OSP (Organic Solderability Preservative) for high-volume consumer products where shelf life is tightly controlled.

It is:

• extremely cost-effective
• perfectly flat for SMT
• ideal for mass production

But it also has:

• shorter shelf life
• greater handling sensitivity

If you don't have 0.4mm-pitch BGAs, don't pay the ENIG tax unless your environment specifically requires the corrosion resistance of gold.

The Hidden Costs of Copper Weight and Layer Count

Increasing layer count is an obvious cost adder, but how you add layers matters.

• Moving from 2 → 4 layers is usually a major jump
• Moving from 4 → 6 layers is often only 30–40% more

However, many engineers overlook copper weight.

While 1oz copper is standard, 2oz copper requires:

• longer etching times
• wider trace spacing
• tighter manufacturing controls

I've seen boards fail during CAM review because designers requested 2oz copper while still using 4-mil traces.

You simply cannot etch thick copper that precisely.

If you need 2oz copper for power delivery, increase your minimum trace width and spacing to at least:

• 8 mil
• preferably 10 mil

Otherwise, the fab house may charge additional engineering fees—or manufacture the boards with lower yields that you ultimately pay for.

Simplifying the Solder Mask and Silkscreen

Green is the standard solder mask color for a reason.

Fabricators run green solder mask lines continuously. When you request:

• matte black
• white
• purple
• custom colors

they often must:

1. stop the production line
2. clean screens
3. swap chemistry

That creates:

• setup charges
• longer lead times
• reduced throughput

Unless the PCB is customer-facing or requires specific optical/thermal properties (such as white solder mask for LED boards), stick with green.

Similarly, keep silkscreen on one side whenever possible.

Double-sided silkscreen requires:

• two print passes
• two curing cycles

Also ensure your silkscreen text is at least 0.15mm (6 mil) wide. Anything smaller often becomes unreadable, meaning you’re paying for markings that nobody can actually see.

FAQ

Does board shape affect price?

Yes.

Rectangular boards are cheapest because they can be easily V-scored. Circular or complex outlines require routing, which increases CNC time and creates more panel waste.

Is V-scoring cheaper than tab-routing?

Generally, yes.

V-scoring is a fast blade-based process, while tab-routing requires router bits and more complex programming.

Use V-scoring whenever:

• the board is rectangular
• components do not overhang the edges

How much does via-in-pad cost?

A lot.

Via-in-pad requires:

1. epoxy filling
2. copper plating over the filled via (POFV)

This adds several manufacturing steps and can increase PCB cost by 25% or more.

What is the most expensive part of a PCB stackup?

Usually:

• specialty materials (Rogers, PTFE, high-speed laminates)
• blind/buried vias

In many cases, adding two extra signal layers is cheaper than implementing blind vias.

Summary

Reducing PCB cost isn't about finding the cheapest factory.

It’s about designing a board that is easy to manufacture.

If you:

• optimize panel utilization
• stay within standard drill sizes
• avoid exotic finishes
• use standard materials and colors

you naturally reduce costs while improving yields and reliability.

The best way to save money is to treat your PCB Manufacturer as a partner early in the design phase. Ask for their capability matrix and design your board around their most efficient processes.